onno
New Member
Posts: 15
|
Post by onno on Apr 16, 2018 20:43:52 GMT 2
Hi Hannes,
For some reason it's not working in my environment. I connected all corresponding wires. Set up the mobiflight configuration but still no luck. I thought maybe the segment display was broken, replaced it.. still no luck.
In the configuration of AlbEagle, he's using the max chip instead of the PCB. In my situation I'm using the PCB. Check my earlier photo in this thread.
What to do?!
|
|
|
|
Post by AlbEagle on Apr 16, 2018 23:11:23 GMT 2
Hi Hannes, For some reason it's not working in my environment. I connected all corresponding wires. Set up the mobiflight configuration but still no luck. I thought maybe the segment display was broken, replaced it.. still no luck. In the configuration of AlbEagle, he's using the max chip instead of the PCB. In my situation I'm using the PCB. Check my earlier photo in this thread. What to do?! Should be the same. The only difference is the possibility to remove/replace 7 segment displays but wiring should be the same. Do you get any numbers or nothing at all. |
|
onno
New Member
Posts: 15
|
Post by onno on Apr 17, 2018 20:08:19 GMT 2
Hi Hannes, For some reason it's not working in my environment. I connected all corresponding wires. Set up the mobiflight configuration but still no luck. I thought maybe the segment display was broken, replaced it.. still no luck. In the configuration of AlbEagle, he's using the max chip instead of the PCB. In my situation I'm using the PCB. Check my earlier photo in this thread. What to do?! Should be the same. The only difference is the possibility to remove/replace 7 segment displays but wiring should be the same. Do you get any numbers or nothing at all. Hi AlbEagle, I have attached some screenshots of my current situation. The Mobiflight window shows the test. The other images are from my current set up. |
|
|
|
Post by AlbEagle on Apr 20, 2018 13:21:40 GMT 2
Should be the same. The only difference is the possibility to remove/replace 7 segment displays but wiring should be the same. Do you get any numbers or nothing at all. Hi AlbEagle, I have attached some screenshots of my current situation. The Mobiflight window shows the test. The other images are from my current set up. Well it depends how you connected the wires. If you connected them using my schematics than let me know. If you connected them using hannes schematics than he has to tell where to put the tick on the characters. That could be the problem in your case. |
|
onno
New Member
Posts: 15
|
Post by onno on Apr 21, 2018 17:34:41 GMT 2
Hi AlbEagle, I have attached some screenshots of my current situation. The Mobiflight window shows the test. The other images are from my current set up. Well it depends how you connected the wires. If you connected them using my schematics than let me know. If you connected them using hannes schematics than he has to tell where to put the tick on the characters. That could be the problem in your case. I've welded them as Hannes description. In your example youve welded them straight to the chip? |
|
|
|
Post by AlbEagle on Apr 22, 2018 1:41:22 GMT 2
Then hannes has to share his config for NM and KT because he has used different letters.
|
|
|
|
Post by hannes1 on Apr 22, 2018 6:46:36 GMT 2
Hy
In Page one in this topic Therme are all pictures off my wireing and my MF config. Take a look. You need more,than write me again. Thanks
|
|
|
|
Post by hannes1 on Apr 23, 2018 6:13:01 GMT 2
|
|
|
|
Post by hannes1 on Apr 23, 2018 13:41:39 GMT 2
Again the whole clean together. I hope this helps. friendly greetings Hannes
|
|
onno
New Member
Posts: 15
|
Post by onno on Apr 23, 2018 22:04:45 GMT 2
Many many thanks. Will try tomorrow night and will let you know! |
|
|
|
Post by Filip Dymák on Apr 5, 2019 20:24:01 GMT 2
Hello, I am working on NM KT display. I did that the same way accoarding to your schematic. But I amd getting instead of NM nonsence.
I am sending the picture.
I bought 14 segment display (with common anode)
Can you tell me what is wrong?
I think that I need comon catode.
Thank you very much
Filip Dymák (Czech Republic) ![]()  |
|
|
|
Post by AlbEagle on Apr 24, 2019 18:55:30 GMT 2
Hello, I am working on NM KT display. I did that the same way accoarding to your schematic. But I amd getting instead of NM nonsence. I am sending the picture.
I bought 14 segment display (with common anode) Can you tell me what is wrong? I think that I need comon catode.
Thank you very much You need Common Cathode displays. |
|
|
|
Post by hector on May 8, 2019 23:15:43 GMT 2
Someone who can tell me if there is a PCB, for Radio Stack, since I will use Displays of this type already with the integrated chip Max7219, I would be very grateful if you help me thanks  |
|
|
|
Post by above1 on Jan 30, 2021 16:02:23 GMT 2
|
|
