|
|
Post by emecreativelab on Aug 3, 2020 9:34:17 GMT 2
Hi!where can I get the dual encoders ? There are instructions for DIY, but I'm wondering if these will work? Dual encodersI think they gotta fit the 3d printed plate |
|
|
|
Post by emecreativelab on Aug 3, 2020 9:35:15 GMT 2
They are some resistors. Like R6 and R29 that are not listed in the picture for the radio stack V2. What should we do with those?
|
|
|
|
Post by davbow on Aug 3, 2020 21:24:27 GMT 2
Anyone been able to order boards with the current Gerber files? If so, who made them for you. My go to source cannot validate the files.
|
|
|
|
Post by eloute on Aug 11, 2020 20:13:59 GMT 2
I'd like to get my hands on one of these boards but it seems like there are issues that need to be ironed out in order for manufacturing can happen.
With the new Sim coming out, I'd imagine there would be some interest in keeping this project going.
|
|
mbuto
New Member
Posts: 5
|
Post by mbuto on Aug 21, 2020 0:35:06 GMT 2
Anyone been able to order boards with the current Gerber files? If so, who made them for you. My go to source cannot validate the files. Yes. A guy here in the Vancouver area, but they were physically done in China. |
|
|
|
Post by eloute on Aug 23, 2020 16:15:57 GMT 2
Anyone been able to order boards with the current Gerber files? If so, who made them for you. My go to source cannot validate the files. Yes. A guy here in the Vancouver area, but they were physically done in China. That's great, any chance you could pass on this information so we could order some boards? I'm in Toronto and would like to start this part of my project. Thanks |
|
mbuto
New Member
Posts: 5
|
Post by mbuto on Aug 24, 2020 7:12:19 GMT 2
They gave me a 2nd set, so I can sell them to you. However, there's an outstanding snag - 2 resistors on the board are not on the parts list. I'm trying to hunt this info down. When I do, I'll let you know and we can figure out something to get those boards to you.
|
|
|
|
Post by eloute on Aug 24, 2020 15:40:35 GMT 2
They gave me a 2nd set, so I can sell them to you. However, there's an outstanding snag - 2 resistors on the board are not on the parts list. I'm trying to hunt this info down. When I do, I'll let you know and we can figure out something to get those boards to you. That's Great I appreciate that. I'll send you a direct message with my info. I'd really like to keep this project alive. The original guy put so much work into this, it'll be a shame it dies off |
|
|
|
Post by AlbEagle on Aug 24, 2020 17:01:14 GMT 2
They gave me a 2nd set, so I can sell them to you. However, there's an outstanding snag - 2 resistors on the board are not on the parts list. I'm trying to hunt this info down. When I do, I'll let you know and we can figure out something to get those boards to you. Hi there, which resistors are you referring to? Regards AlbEagle |
|
|
|
Post by AlbEagle on Aug 24, 2020 17:30:39 GMT 2
They gave me a 2nd set, so I can sell them to you. However, there's an outstanding snag - 2 resistors on the board are not on the parts list. I'm trying to hunt this info down. When I do, I'll let you know and we can figure out something to get those boards to you. Hi there, which resistors are you referring to? Regards AlbEagle R29 is the middle resistor and it goes from (OMI lights) in this case is the I to pin 4 in the middle LED Pins. R6 is between NAV1 Pot and NAV1 Switch and connects to the MAX Nav1 Active chip. R29 is 220 Ohm R6 is 10kOhm Regards AlbEagle |
|
|
|
Post by polarair on Aug 31, 2020 10:32:51 GMT 2
AlbEagle,
Do you have a componant list, as i see some differences in the listing and the links to the components on the site. In the list you speak about 100nf capacitors and in the buying list they are 50V 0.1uF.
As im new to electronics it would be nice to have a BOM (list) for the Radio stack this makes it easier to buy all the componants.
Mike
PS ordered the PCB boards today at the Hongkong company.
|
|
|
|
Post by AlbEagle on Aug 31, 2020 10:50:02 GMT 2
AlbEagle, Do you have a componant list, as i see some differences in the listing and the links to the components on the site. In the list you speak about 100nf capacitors and in the buying list they are 50V 0.1uF. As im new to electronics it would be nice to have a BOM (list) for the Radio stack this makes it easier to buy all the componants. Mike PS ordered the PCB boards today at the Hongkong company. Hi Mike, The list remains the same, links have probably changed because i have posted them a while back and i didn't have time to check them but it should be easy to search on ebay or aliexpress. Regarding the capacitors, it is the same, 100 nf is the same as 0.1 uf. If you want to search in nf then search for 100nf, if you want to search with uf than look for 0.1 uf. Regards AlbEagle |
|
|
|
Post by davbow on Sept 4, 2020 19:01:11 GMT 2
AlbEagle, Do you have a componant list, as i see some differences in the listing and the links to the components on the site. In the list you speak about 100nf capacitors and in the buying list they are 50V 0.1uF. As im new to electronics it would be nice to have a BOM (list) for the Radio stack this makes it easier to buy all the componants. Mike PS ordered the PCB boards today at the Hongkong company. Can you tell me what company you used? My normal source cannot validate the current Gerber files . . . |
|
|
|
Post by polarair on Sept 4, 2020 20:08:44 GMT 2
Davbow,
My boards will arrive monday, so if they look good i willing to part with a set. PM me for details
AlbEagle,
Thanks, its been a while to be into electrionics. Building this Radio Stack is going to be a challange but fun, i will be using the strips as show in your second example, i believe its easier than building all the modules.
Will be printing the Faceplates with a 3D printer Prusa or will get them done with a CNC/Router and Laser engraver, waiting for the qoute.
As for the rest im folloing your site so expect it will all work.
Great Job,
Mike
|
|
|
|
Post by Michael on Sept 14, 2020 17:07:57 GMT 2
Hi everyone, I have found some free time lately and I have done some fixes in the Radiostack and Arduino Shield. Changes: 1. Fixed the Transponder 5 pin switch alignment, now the 5 position switch should fit in place 2. Fixed GND Pin issue in the Encoder, Switches and Leds connections 3. Radiostack pins aligned with Arduino Shield pins. 4. Arduino's extra ports (the rest of them) now usable Before I publish the gerber files, if you guys have any other issues, let me know and i will fix it (or maybe if you list all the issues you have had and I will go one by one and fix them). Direct link to the website LINK |
|
