bosal
New Member
Posts: 42
|
Post by bosal on Sept 30, 2020 21:08:08 GMT 2
Can someone send me a link of the component needed for "PWR SW", "COM1 POT" and "NAV1 POT"?
IOn the website it seems a pot-meter like on the picture below, but how do you mount it on the PCB?  Does anybody has a detailed picture on how to do? Thanks!
Attachments:
|
|
|
|
Post by davbow on Sept 30, 2020 22:01:45 GMT 2
It does not get mounted on the PCB - it is mounted on a panel somewhere. It controls the backlight for the push buttons. If you are not using lighted buttons you do not actually need it. I will post a link.
|
|
|
|
Post by davbow on Sept 30, 2020 22:12:46 GMT 2
|
|
bosal
New Member
Posts: 42
|
Post by bosal on Oct 1, 2020 10:59:49 GMT 2
It does not get mounted on the PCB - it is mounted on a panel somewhere. It controls the backlight for the push buttons. If you are not using lighted buttons you do not actually need it. I will post a link. Ok, I understand! Thanks! |
|
andy
New Member
Posts: 2
|
Post by andy on Oct 5, 2020 16:18:25 GMT 2
Does anyone have extra boards for sale? I'm looking for both the radio board and the arduino board. Just contact me here. Thanks!
|
|
|
|
Post by polarair on Oct 5, 2020 17:19:59 GMT 2
I have boards. Main and arduino.
UPDATE:
Boards are about 25EURO per set excluding shipping. I spend about this on the set of 5 boards from HongKong and defided this by 5. So its a fair price. Im based in The Netherlands and shipping in Europe makes all easier.
Mike
|
|
andy
New Member
Posts: 2
|
Post by andy on Oct 6, 2020 16:40:25 GMT 2
I have boards. Main and arduino. Pm me for how and price. I need no profit so ill slip cost ex shipping Sent you a PM |
|
|
|
Post by polarair on Oct 16, 2020 21:23:51 GMT 2
DONE
got the HARdWARE Radio stack working all displays are working and looks good, now the is the time for the code, not easy but we will work on it Airmanager code. I implemented PODs for the com and nav without a switch. But that should be ok.
Only issue is that the small switches are to low and there is no way to raisethem, so i will print a 3d item to raise them to the hight of the face plate. Als there is still the need to rebuild the faceplate.
Biut 1st phase done!!
PS the Compass is getting there but we need to modfy all as there is no home point. Working with some of the AM guys to get the sensor inside the compass.
Mike
|
|
|
|
Post by davbow on Oct 16, 2020 21:29:46 GMT 2
DONE
got the HARdWARE Radio stack working all displays are working and looks good, now the is the time for the code, not easy but we will work on it Airmanager code. I implemented PODs for the com and nav without a switch. But that should be ok.
Only issue is that the small switches are to low and there is no way to raisethem, so i will print a 3d item to raise them to the hight of the face plate. Als there is still the need to rebuild the faceplate.
Biut 1st phase done!!
PS the Compass is getting there but we need to modfy all as there is no home point. Working with some of the AM guys to get the sensor inside the compass.
Mike
Nice work. I think I have some soldering defects. Digits do not light up correctly for all the modules. I am going to have to go back and re-evaluate. I am excited to hear more about your Airmanager progress! David |
|
bosal
New Member
Posts: 42
|
Post by bosal on Oct 16, 2020 22:00:23 GMT 2
DONE
got the HARdWARE Radio stack working all displays are working and looks good, now the is the time for the code, not easy but we will work on it Airmanager code. I implemented PODs for the com and nav without a switch. But that should be ok.
Only issue is that the small switches are to low and there is no way to raisethem, so i will print a 3d item to raise them to the hight of the face plate. Als there is still the need to rebuild the faceplate.
Biut 1st phase done!!
PS the Compass is getting there but we need to modfy all as there is no home point. Working with some of the AM guys to get the sensor inside the compass.
Mike
Good job!
|
|
|
|
Post by polarair on Oct 17, 2020 11:54:47 GMT 2
Nice work. I think I have some soldering defects. Digits do not light up correctly for all the modules. I am going to have to go back and re-evaluate. I am excited to hear more about your Airmanager progress! David Make sure you connect the Arduino boards, mine did not work correctly and intermitent till i connected the boards. I also made a mistake, i forgot one resistor so one of the segments did not light up, solderer was ok but just forgot one 10K. Fixed and works. Now it programming time and faceplate time. |
|
kci
New Member
Posts: 4
|
Post by kci on Oct 18, 2020 19:04:07 GMT 2
Hey guys, if anyone needs the Shield i bought it from JLCPCB and have 4 extra ones... so if you want to buy them  I am from germany and I would sell bouth of them for 25 Euros + Shipping  |
|
|
|
Post by polarair on Oct 18, 2020 23:20:55 GMT 2
Sorry i spend more. Around 20 euros for the boards.
|
|
|
|
Post by eloute on Oct 27, 2020 20:57:49 GMT 2
Sorry i spend more. Around 20 euros for the boards. 20 euros for the boards was a great price. I spent $165 for my set |
|
|
|
Post by above1 on Oct 29, 2020 16:53:47 GMT 2
Hello and greetings to everyone! I came across this site as I am starting my journey to build a Cessna 172 cockpit for myself and my 15yr old son. He has taken an interest in becoming a pilot and I thought doing this would be a great father & son project as he learns to fly planes. With that, I would like to know if anyone else here has an extra set of v2 radio stack PCB boards that they would sell and ship to me. I figured I'd get this part first, build the radio stack, and then hopefully, everything that follows will be easier. I live in the US. Specifically Seattle, WA.
Thank you and I look forward to speak with everyone here.
Larry
|
|
