7 Segment Display Issue

jonathan
New Member

Posts: 3

7 Segment Display Issue Dec 30, 2020 9:31:34 GMT 2

Quote

Post by jonathan on Dec 30, 2020 9:31:34 GMT 2

Hi all

i tried to configure the Radio panel and have a lot of issues.. the main issue is this:

I saw those displays stay on always, when i tried to test those displays on Mobiflight it dosent blink like other displays..

tried to switch the IC of them..still the same.

in addition i cant config the Xpdr, Dme and Adf buttons ..dont know yet if this is connect to the above problem or just need to do a better job with offsets on Mobiflight

in my opinion i think all the sector of this panel not functional(displays and buttons) fore some reason..and one have any idea?

Last Edit: Dec 30, 2020 9:36:16 GMT 2 by jonathan

kklee6
Junior Member

Posts: 87

7 Segment Display Issue Dec 30, 2020 12:38:32 GMT 2

Quote

Post by kklee6 on Dec 30, 2020 12:38:32 GMT 2

Hi Jonathan,

I think those ADF and Xponder buttons are not yet supported in FSUIPC so we have to wait

.

As for the 7-segment displays, you can test them one by one.

If both circuitry and configuration are alright, they should look like these:

BTW, make sure that you power up the PCB with an external 5V supply.

Regards,
KK

jonathan
New Member

Posts: 3

7 Segment Display Issue Dec 30, 2020 12:55:53 GMT 2

Quote

Post by jonathan on Dec 30, 2020 12:55:53 GMT 2

hi all other display work fine
only the ADF , XPNDR and NM, KT not work..

in addition i just tried the files from here:

flyingforfun.freeforums.net/thread/158/radiostack-v2-display-issues

same.. the ADF and XPNDR show 000000
and KT and NM show something else..

kklee6
Junior Member

Posts: 87

7 Segment Display Issue Dec 30, 2020 14:22:02 GMT 2

Quote

Post by kklee6 on Dec 30, 2020 14:22:02 GMT 2

In my experience, if only the PCB is powered and the arduino boards are not connected, the 7-segment displays light up (just like those in your ADF and XPNDR).

Then plug in the USB cables connected to the arduino boards and run Mobiflight (but not connected to the Sim yet), all the LEDS go out (I believe they are reset and ready.)

Then connect to MSFS via FSUIPC and the displays should work properly.

If, in your case, those 7-segment displays do not go out. There are something wrong with either the circuitry in the PCB or the arduino board (most like the ENCODERS RADIO one).

Hope it helps.

KK

kklee6 Junior Member Posts: 87	7 Segment Display Issue Dec 30, 2020 14:53:46 GMT 2 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by kklee6 on Dec 30, 2020 14:53:46 GMT 2 Using the files you get from the post (flyingforfun.freeforums.net/thread/158/radiostack-v2-display-issues ), it should look like this if everything is ok:

jonathan New Member Posts: 3	7 Segment Display Issue Dec 31, 2020 10:33:59 GMT 2 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by jonathan on Dec 31, 2020 10:33:59 GMT 2 ok then. so you can tell me, all ADF,DME button not working for me.. you managed to sync them with Mobiflight ?

kklee6 Junior Member Posts: 87	7 Segment Display Issue Dec 31, 2020 11:22:11 GMT 2 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by kklee6 on Dec 31, 2020 11:22:11 GMT 2 The buttons do not work for me neither. I was not able to find the offsets to configure them and I think it is FSUIPC problem.

Flyingforfun

7 Segment Display Issue

Post by jonathan on Dec 30, 2020 9:31:34 GMT 2

Post by kklee6 on Dec 30, 2020 12:38:32 GMT 2

Post by jonathan on Dec 30, 2020 12:55:53 GMT 2

Post by kklee6 on Dec 30, 2020 14:22:02 GMT 2

Post by kklee6 on Dec 30, 2020 14:53:46 GMT 2

Post by jonathan on Dec 31, 2020 10:33:59 GMT 2

Post by kklee6 on Dec 31, 2020 11:22:11 GMT 2

Quick Reply